You've laid your fibreglass matting, but the job isn't finished. Perhaps you're adding a second layer, joining onto yesterday's laminate or preparing to apply topcoat. Do you need to wipe the GRP with acetone before carrying on? Quick answer: Not normally when you're applying compatible fibreglass layers wet-on-wet within the manufacturer's permitted working window. If the existing GRP has fully cured, been left exposed, become contaminated or already received a topcoat, you may need to clean and mechanically prepare it before adding material. An acetone wipe is required for some systems and procedures, but it is not a universal bonding treatment. Always follow the installation instructions for your exact resin and topcoat. This guide explains what acetone does, how to approach next-day GRP joints, what to check before topcoating and when to stop work rather than risk a poor bond. Important: This is general advice for polyester GRP roofing, not a substitute for the technical data sheet (TDS), safety data sheet (SDS) and installation instructions supplied with your chosen system. These take priority, including for overlap widths, surface preparation, catalyst ratios and recoat windows. Why Acetone Isn't a GRP Primer Polyester GRP roofing resin cures through a reaction initiated by the specified catalyst. While a laminate is being applied, fresh resin and reinforcement can be combined within the system's permitted working period. Once a laminate is cured, the condition of its surface becomes particularly important for any further application. Acetone is a solvent commonly used to clean uncured polyester resin from suitable tools. Some GRP roofing instructions also specify an acetone wipe when preparing a cured or delayed surface. However, acetone does not replace abrasion, remove the need to inspect a damaged laminate or guarantee adhesion. It should never be added to roofing resin or topcoat unless a product manufacturer explicitly specifies a compatible formulation and procedure. For suitable cleaning applications, see our Acetone/Brush Cleaner 99.9% Pure. Check your system instructions before using any solvent on a roof surface. Acetone/Brush Cleaner 99.9% Pure For cleaning suitable tools and uncured resin residues. View Product Do You Need Acetone? A Quick Decision Guide Situation What to check or do Acetone? Adding another layer wet-on-wet Continue within the approved laminating window and consolidate the matting properly. Usually not needed. Previous laminate has started to set Check whether the system still permits direct overlaminating and whether the laminate is in suitable condition. Follow the system instructions. Joining onto yesterday's fully cured GRP Check the permitted recoat window; inspect, clean and abrade the overlap area where specified. Use only if specified for the joint. Dust, grease, dew or rain on the laminate Stop and address contamination or moisture. Check cure and condition before preparing the surface. Not a substitute for drying or repair. Overlaminating an existing topcoated roof Identify the original system, assess adhesion and damage, and use an approved repair or refurbishment method. System-specific. Topcoating later than recommended Follow the topcoat manufacturer's delayed-application procedure. Some systems specify a wipe. Remember: A clean-looking laminate is not necessarily ready for another layer. A surface can appear dry while still being too soft to abrade, contaminated or outside the manufacturer's permitted bonding window. How to Join New Fibreglass to Yesterday's GRP Splitting a roofing job over two days is sometimes unavoidable. The key is to treat the join as a planned detail rather than assume new resin will bond to anything beneath it. The following sequence is a general checklist: use the exact preparation method and overlap measurement stated for your GRP system. Identify the material and check the instructions. Confirm which resin, reinforcement and topcoat were used, how long the laminate has cured and whether the manufacturer permits the proposed overlap. Inspect the existing laminate. Look for soft areas, poor consolidation, lifted matting, bubbles, damp patches, frost, dirt and signs of contamination. Do not build over a defective area. Confirm that the surface is fully dry. Overnight dew and condensation matter even if no rain has fallen. If water reached uncured resin, the affected area may need more than drying. Mark the approved overlap area. Use the manufacturer's required overlap width. Some systems specify particular widths and methods for ordinary laps, repairs and damaged sections; they are not interchangeable. Prepare the surface as directed. On cured GRP, this may involve abrading the bonding area to remove gloss and create the required mechanical key. Use the abrasive grade stated in the instructions; protect yourself from sanding dust. Remove dust and clean if specified. Use suitable dust extraction or another approved method. If an acetone wipe is required, follow the SDS and application instructions; use a suitable clean cloth and keep solvent away from ignition sources. Allow any permitted cleaner to evaporate fully. Never laminate onto pooled solvent or a surface that is still wet with cleaner. Apply and consolidate the new laminate. Mix the resin and catalyst only as directed. Wet out the reinforcement thoroughly and use a consolidating roller to remove trapped air, especially at the transition. GRP Consolidating Rollers Helps remove trapped air from resin-wetted fibreglass. View Product Complete the finish to the system specification. Check the overlap profile, trim details and curing requirements before topcoating. Topcoat is not a substitute for correcting a badly formed lap or an unsound joint. Planning tip: If you expect to stop at the end of the day, plan where the next section will join. Protect the unfinished work from rain, debris and overnight condensation, and consult the manufacturer's procedure for a delayed joint. How Long Should You Wait Between Fibreglass Layers? There is no single waiting time that applies to every GRP roofing resin. A batch's working life, the point at which the laminate gels, its initial cure and the time it can safely be walked on are different stages. Stage What it means What to follow Pot life / working time How long the mixed resin remains workable in its container. Product mixing chart and batch size guidance. Gel / initial set The resin begins to lose flow and the laminate starts to set. Manufacturer's application and overlaminating window. Ready for topcoat The laminate has reached the condition required for its compatible topcoat. Topcoat instructions, including maximum time between stages. Light access The cured surface may support the access allowed by the system. System-specific cure and access advice. Full cure / service The finished system achieves its specified service condition. Technical data sheet and actual site conditions. Air temperature, substrate temperature, material temperature, humidity, batch size and catalyst dosage can all affect curing. Do not increase the catalyst beyond the specified mixing range or assume that a tacky surface automatically means the resin has failed. Laminating resins can retain surface tack, but a persistently soft, wet or rubbery laminate needs investigation before work continues. For colder conditions, read our guide to curing GRP resin in cold weather, alongside the instructions for your specific product. Can You Apply GRP Topcoat the Next Day? Often, yes — provided the laminate is sound and the application falls within the system's permitted topcoating window. Do not rely solely on the fact that the laminate feels hard. For example, published Cure It GRP installation guidance calls for topcoating within 24 hours and sets out an acetone-wipe procedure when topcoating is delayed beyond that period. That is an example from one system, not a rule for every Apex GRP kit. Other products may specify different timing and surface preparation. Never transfer a preparation method from one manufacturer's topcoat to another without checking compatibility. If the laminate was exposed to dust, moisture or other contamination overnight, assess and prepare it according to the manufacturer before applying topcoat. See also our GRP roof topcoat and recoating guide. GRP Roofing Topcoat / Free Catalyst Protective finishing coat for compatible GRP roofing systems. View Product What If It Rained on Your GRP Laminate Overnight? Do not laminate or topcoat over a wet surface. First determine whether the existing laminate had already cured properly when the rain, dew or frost arrived. Remove standing water safely, allow the surface to dry and inspect it for discolouration, soft patches, blisters, lifting or poor adhesion. If moisture reached resin before it cured, or if the laminate is soft or visibly damaged, simply waiting for the surface to dry may not be enough. Follow the system's repair instructions or seek technical advice before proceeding. Acetone must never be used as a shortcut for drying a wet roof. On a cold morning, check the deck and laminate temperature as well as the air temperature. A surface can be at risk of condensation even when the air does not feel particularly cold. Can You Fibreglass Over an Existing GRP Roof? Sometimes, but it depends on the condition and identity of the existing roof. A sound, compatible surface may be suitable for an approved repair or overlay procedure. A roof with widespread delamination, trapped moisture, movement or damaged decking needs a proper assessment first. Existing topcoat can create a different bonding surface from fresh laminating resin. Do not assume that an acetone wipe alone prepares it for new reinforcement. Check the refurbishment method, including whether abrasion, removal of defective material or additional preparation is needed. For a complete installation overview, see How to Fibreglass a Flat Roof: Step-by-Step Guide. Do You Need More Than One Layer of Fibreglass Matting? Many domestic GRP flat-roof systems use one specified layer of chopped strand matting with compatible laminating resin and topcoat. Other applications may use heavier reinforcement or multiple layers. The correct specification depends on the complete system, intended use, substrate, loads and required finish — not simply whether 450g or 600g matting appears stronger. Compare reinforcement options in our chopped strand mat weight guide, or browse our GRP roofing kits. For roof size and material planning, use the GRP Kit Calculator. Can You Lay GRP Directly onto PIR Insulation? For conventional polyester GRP roofing systems designed for timber decking, do not laminate directly onto exposed PIR insulation. The roof needs a substrate approved for the chosen system. Some warm-roof specifications use a suitable timber-based overlay above the insulation, but deck type, thickness, fixings, vapour control and the full roof build-up must be checked against the manufacturer's specification and project requirements. Do not assume that one generic build-up suits every roof. What Can You Use Instead of Acetone? The answer depends on what you are cleaning. Cleaning uncured resin from tools is not the same task as preparing a cured GRP surface for bonding. For suitable tools: acetone brush cleaner may be used where the tool and product instructions allow it. For some tool-cleaning tasks: a dedicated alternative such as TriKlean may be appropriate. Check the product instructions and current availability. Do not assume a tool cleaner is approved as a pre-laminating surface wipe. For small jobs: disposable or replaceable applicators can reduce the need to clean cured resin from tools. For cured joint preparation: use only the cleaner and preparation method specified for your roofing system. Substituting another solvent without approval can create bonding problems. Never use acetone or other solvents to clean resin from your skin. Five Common GRP Overlaminating Mistakes Using acetone as a primer. A solvent wipe cannot replace the required surface preparation or repair. Working over dew or damp GRP. Moisture can interfere with a sound bond and requires investigation. Ignoring the recoat window. 'Yesterday' is not enough information; temperature, product and actual cure condition all matter. Failing to consolidate the new matting. Trapped air and poorly wetted reinforcement can compromise the laminate. Using too much catalyst to speed things up. Mix only within the stated product limits and never add unapproved thinners. When Should You Stop Rather Than Carry On? Pause the job and obtain product-specific advice if the laminate remains unexpectedly soft or rubbery, shows blistering or delamination, contains trapped water, has been contaminated before curing, or sits on a moving or damaged deck. Also stop if the surface temperature or weather conditions fall outside the permitted installation range, or if you do not know whether an old roof coating is compatible with your new resin. Covering a defective section with another layer or topcoat does not necessarily correct the underlying problem. Safety: Acetone, Resin, Catalyst and GRP Dust Before starting, read the current labels, TDS and SDS for every product. Follow site risk assessments and relevant COSHH controls. Polyester resin vapours, organic peroxide catalysts, acetone and dust from GRP abrasion present different hazards. Work with adequate ventilation and the specified protective gloves, eye protection and any respiratory protection indicated by the risk assessment and SDS. Keep acetone and other flammable materials away from heat, sparks, naked flames and smoking. Handle MEKP catalyst strictly as instructed; keep it away from incompatible substances, including acetone, and never mix it directly with solvents. Control sanding dust, use suitable extraction and avoid dry sweeping where it could spread airborne fibres or dust. Store used solvent wipes and chemical waste safely and dispose of them according to product and local waste guidance. Never use solvents on your skin. Use appropriate skin-cleaning products instead. For further UK safety guidance, see the Health and Safety Executive's guidance on solvents in construction. Frequently Asked Questions Do you need acetone between layers of fibreglass? Normally not for compatible wet-on-wet layers applied within the manufacturer's working window. For cured or contaminated GRP, follow the specified surface preparation procedure; some systems call for an acetone wipe and others use different methods. Can I fibreglass over yesterday's work? Often yes, if the existing laminate is sound, dry and suitably prepared. Check the exact system's overlap, abrasion, cleaning and curing instructions before you begin. Can I apply fibreglass to a damp surface? Do not apply conventional polyester GRP roofing to a damp surface unless the particular system explicitly approves that condition. Dew, frost and rain contamination need to be dealt with first. How long should I wait before applying GRP topcoat? Follow your chosen laminate and topcoat instructions. The surface must reach the required cure condition, and many systems also specify a maximum time before additional preparation becomes necessary. What happens if I leave GRP laminate overnight without topcoat? It may still be possible to topcoat the following day, but check the permitted topcoat window and whether the exposed surface needs cleaning or other preparation. Inspect for dew and contamination before continuing. Can acetone be added to GRP roofing resin to thin it? Do not add acetone as an improvised thinner. Use only additives and mixing instructions specifically approved by the resin manufacturer. Does acetone remove the need to sand cured fibreglass? No. Where mechanical keying is required, wiping with acetone does not replace abrasion. Follow the system's full preparation procedure. Can GRP be laminated directly onto PIR boards? Not with conventional timber-deck polyester GRP roofing systems. Use an approved substrate and complete roof build-up specified for the system. Ready to Start Your GRP Roofing Project? ▤GRP ROOFING KIT Resin · Matting · Topcoat · Tools Plan your roof materials and explore compatible GRP roofing kits, trims and tools. Our calculator helps you choose materials based on your project measurements. Use Our GRP Kit Calculator Prefer to browse? View GRP Roofing Kits. Need advice on a difficult joint? Call Apex on 0800 612 7903 with your system name and roof details ready. Related guides: How to Fibreglass a Flat Roof · How to Cure GRP Resin in Cold Weather · Can You Paint a Fibreglass Roof?